|
|
|
| HEAVYGEL EFX - Industrial Water Cooled Water Chiller
|
|
With the new Water Cooled Chiller Heavygel EFX, Frigel sets new standards for Process Cooling, introducing the use of the most efficient technologies available today.
The introduction of High Efficiency Screw Compressor and Oil Free Centrifugal Compressor make available chillers with efficiency that cannot be compared with all the other traditional chillers.
HEAVYGEL EFX
THE MOST EFFICIENT CHILLERS IN PROCESS COOLING
In developing the new EFX chiller line, Frigel has paid utmost attention to the concept of "Total Cost of Ownership", well aware that the initial investment cost of a water chiller is a minimal part of the overall running costs that chiller will generate during its lifetime.
Energy use, installation, maintenance and dismantling costs, downtimes and service costs, must all be carefully considered and evaluated to make a smart decision when the time to invest in a new process chiller comes.
With the clear objective of minimizing the ??otal Cost of Ownership", for our Customers, we have designed the new EFX chiller line, with the following features:
MINIMUM ELECTRICAL CONSUMPTION
The Compressors of the EFX chillers have been selected according to the highest Energy efficiency obtainable today.
Note: EER (Energy Efficiency Ratio) indicates the electrical performance of a chiller.
The above chart shows the full and part load performance curves of the compressors used on the EFX chillers compared with a typical oil-flooded screw compressor on a 300 kW (90-ton) water-cooled chiller.
The three types of compressors used on the EFX chillers line are much more efficient compared to traditional compressors.
The Energy Savings that can be achieved with the EFX Chillers can widely justify eventual higher costs of the initial investment.
The amount of savings obviously depends on two variables: the cost of energy and the running hours.
The table that follows can give an idea of the impact of the energy consumption on the Total Cost of Ownership for a process chiller.
SIMPLE AND MODULAR INSTALLATIONS
EFX chillers are designed to minimize the footprint (almost 50% less than a standard water cooled chiller having same capacity) as well as installation and expansion costs.
Increasing Cooling Capacity is extremely easy, allowing an investment proportional to the need of the moment.
A remotable Control Panel manages all the plant: partializing capacity, equalizing the working hours for each unit installed, monitoring the alarms and all working parameters.
A remote control and management of the entire system through a Gateway is also available as an option (more information regarding this feature on last page).
Typical layout of installation of chiller EFX for a plastic injection moulding plant:
RELIABILITY
The choice of high quality components, the design, the control procedures during all assembling phases and a strict final test guarantee the maximum quality of final products.
Moreover, a guarantee of reliability for plants with EFX chillers is given by their modularity and redundancy, typical of all projects made with these machines. The presence of a simple stand-by EFX unit can drastically reduce the plant down-times risks.
EFX 150 MS - WATER-COOLED MULTI-SCROLL COMPRESSOR CHILLER
While the efficiency and reliability of the multi-scroll compressors featured in this unit has already been widely proved all over the world, we have thoroughly optimized its use for process cooling applications, with the intent of maximizing the energetic performances.
Optimized for use with R-407c refrigerant gas.
Very low start-up current.
High performance stainless steel brazed plate condenser and evaporator.
EFX 300 SC - WATER-COOLED HIGH EFFICIENCY SCREW COMPRESSOR CHILLER
employs a Semi-Hermetic High Efficiency Screw compressor, specifically designed for water cooled chillers with low gas compression ratio.
Optimized for use with R-134a refrigerant gas.
Very low start-up currents.
High performance stainless steel brazed plate condenser and evaporator.
EFX 300 TC - WATER-COOLED CENTRIFUGAL OIL-FREE COMPRESSOR CHILLER
This unit features the last generation of centrifugal compressor with Magnetic-levitation bearings.
It provides the best efficiency performance, particularly when operating with partial loads.
Turbine compressor system, driven by brushless motor with inverter.
Totally oil-free operation, thanks to rotation on magnetic bearings (Mag-Lev).
Reduced charge (70% less) of R-134a refrigerant gas.
Very low start-up currents.
Exceptionally silent operation.
Very Compact: 50% less footprint and reduced weight compared to traditional water cooled chillers.
High performance stainless steel brazed plate condenser and evaporator.
|
|
|
|
|
主站蜘蛛池模板：
国产精品夜夜春夜夜爽久久小说|
亚洲成人aⅴ|
无码AV人片在线观看天堂|
国产丝袜精品在线|
亚洲夜色噜噜av在线观看|
久久精品国产再热青青青
|
午夜成人影片|
A级国产片在线观看|
亚洲中文字|
日本一区二区三区视频版|
国产成人高清精品亚洲|
欧美黄网站免费观看|
一本色道久久综合熟妇人妻|
久久伊伊香蕉综合精品|
狠狠综合久久久久综合网小蛇|
欧美精品一区二区三区中文字幕
|
中文字幕A片无码免费看|
欧美顶级metart裸体全部自慰|
九九热精品视频在线|
午夜不卡在线观看|
日韩人妻丝袜美腿中文|
午夜在线观看成人av|
99精品人妻少妇一区|
黑人变态另类videos|
亚洲全网成人资源在线观看|
91精品国产91久久久久|
亚洲天堂高清|
亚洲综合日韩av在线|
免费超爽大片黄|
亚洲最大成人|
四虎影院176|
中文字幕在线视频免费|
成人免费777777被爆出|
人妻精品动漫H无码中字|
免费高清特级毛片A片|
国产一区二区三区四区五区加勒比|
国产精品一亚洲AV日韩AV欧|
精品人妻系列无码天堂|
亚洲va精品va国产va|
中文字幕亚洲人妻一区|
中文人妻第9页|
HEAVYGEL HGL - Industrial Air Cooled Water Chiller
